View MP8606DL_8996497.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

mp8606 6a, 6.5v, fast-transient, synchronous step-down converter mp8606 rev. 1.05 www.monolithicpower.com 1 12/22/2015 mps proprietary information. patent protec ted. unauthorized photocopy and duplication prohibited. ? 2015 mps. all rights reserved. the future of analog ic technology description the mp8606 is a fully-integrated, high- frequency, synchronous, rectified step-down switch-mode converter. it offers a very compact solution to achieve 6a of continuous output current from a 2.9v-to-6.5v input with excellent load and line regulation. the advanced pwm scheme provides fast transient response and eases loop stabilization. the mp8606 integrates a 14m ? high-side switch and an 8m ? low-side synchronous switch for high efficiency without an external schottky diode. fault protections include peak current limiting, hiccup over-current protection, and thermal shutdown. it also has a power- good output. the mp8606 requires a minimal number of readily available standard external components and is available in a 3mmx4mm flip-chip qfn package. features ? 6a continuous output current ? 14m ? internal high-side power switches ? 8m ? internal low-side power switches ? input operation range: 2.9v to 6.5v ? adjustable output down to 0.6v ? programmable switching frequency ? hiccup over-current protection ? programmable soft-start time ? thermal shutdown ? power-good output ? 3mmx4mm flip-chip package applications ? p/asic/dsp/fpga core and i/o supplies ? portable equipment / notebook computers ? network and telecom equipment ? point of load regulators all mps parts are lead-free, halogen free, and adhere to the rohs directive. for mps green status, please visit mps website under quality assurance. ?mps? and ?the future of analog ic technology? are registered trademarks of monolithic power systems, inc. typical application
mp8606 ? 6a, 6.5v synchrono us step-down converter mp8606 rev. 1.05 www.monolithicpower.com 2 12/22/2015 mps proprietary information. patent protec ted. unauthorized photocopy and duplication prohibited. ? 2015 mps. all rights reserved. ordering information part number* package top marking MP8606DL qfn-18 (3mmx4mm) see below * for tape & reel, add suffix ?z (e.g. MP8606DL?z). for rohs compliant packaging, add suffix ?lf (e.g. mp MP8606DL?lf?z) top marking 8606: product code of MP8606DL; mp: mps prefix; y: year code; w: week code: lll: lot number; package reference top view 19 20 21 22 vcc in pgnd pgnd pgnd pgnd pgnd pgnd pgnd bst pgnd sw agnd freq fb ss/trk en pgood 1 2 3 4 5 6 78 9 10 11 12 13 14 15 16 17 18 in in sw sw
mp8606 ? 6a, 6.5v synchrono us step-down converter mp8606 rev. 1.05 www.monolithicpower.com 3 12/22/2015 mps proprietary information. patent protec ted. unauthorized photocopy and duplication prohibited. ? 2015 mps. all rights reserved. absolute maxi mum ratings (1) in to gnd ...................................... - 0.3v to +7v sw to gnd ........................... - 0.3v to v in + 0.3v sw to gnd ........ - 2.5v to (v in + 2.5v) for <50ns fb, en, vcc, pok to gnd ............... - 0.3v to +7v ss/trk to gnd............................... - 0.3v to +7v bs to sw ........................................ - 0.3v to +7v continuous power dissipation (t a = 25c) (2) ................................................................... 2.6w junction temperature ...............................150c lead temperature ....................................260c storage temperature............... - 65c to +150c recommended operating conditions (3) supply voltage v in ..........................2.9v to 6.5v output voltage v out ............... 0.6v to (0.9 x v in ) operating junction temp. (t j ). -40c to +125c thermal resistance (4) ja jc qfn-18 (3mmx4mm).............. 48 ...... 10... c/w notes: 1) exceeding these ratings may damage the device. 2) the maximum allowable power dissipation is a function of the maximum junction temperature t j (max), the junction-to- ambient thermal resistance ja , and the ambient temperature t a . the maximum allowable continuous power dissipation at any ambient temperature is calculated by p d (max) = (t j (max)-t a )/ ja . exceeding the maximum allowable powe r dissipation will cause excessive die temperature, and the regulator will go into thermal shutdown. internal thermal shutdown circuitry protects the device from permanent damage. 3) the device is not guaranteed to function outside of its operating conditions. 4) measured on jesd51-7, 4-layer pcb.
mp8606 ? 6a, 6.5v synchrono us step-down converter mp8606 rev. 1.05 www.monolithicpower.com 4 12/22/2015 mps proprietary information. patent protec ted. unauthorized photocopy and duplication prohibited. ? 2015 mps. all rights reserved. electrical characteristics (4) v cc =v in = v en = 3.6v, t a = 25c, unless otherwise noted. parameters condition min typ max units non-switching supply current v en = v in = v cc v fb = 0.65v 820 945 a no load supply current v en = v in = v cc v fb = 0.6v, io=0a 2 ma shutdown current v en = 0v, v in = v cc = 6.5v -1 1 a high-side switch on-resistance (5) i sw = 300ma 14 m ? low-side switch on-resistance (5) i sw = -300ma 8 m ? sw leakage current v en = 0v; v in = 6.5v v sw = 0v or 6.5v -1 1 a current limit v cc = v in = 5v 8 10 13.5 a one-shot on time r freq = 200k ? , v out =1.2v, v in =5v 170 ns minimum off time (5) 50 ns fold-back off time (5) 2.5 s ocp hold-off time (5) 20 s 2.9v ? v in ? 6.0v 594 600 606 mv feedback voltage 6.0v < v in ? 6.5v 591 600 609 mv feedback current v fb = 0.6v 20 50 na soft start charging current 8 10 a soft stop discharging current 8 10 a en input low voltage 0.4 v en input high voltage 1.6 v v en =2v 2 5 a en input current v en =0v -1 1 a pok upper trip threshold fb with respect to the nominal value -10 % pok lower trip threshold fb with respect to the nominal value -30 % pok deglitch timer 0.4 0.6 ms pok output lower voltage i sink =5ma 0.4 v pok leakage current v pok =3.3v -10 10 na standby mode delay time (5) 10 s bs refresh period (4) in standby mode 20 s bs refresh on time (5) in standby mode 100 ns v cc under voltage lockout threshold rising edge 2.4 2.7 2.9 v v cc under voltage lockout hysteresis 300 410 mv thermal shutdown rising edge, hysteresis=20c 160 c note: 5) guaranteed by design.
mp8606 ? 6a, 6.5v synchrono us step-down converter mp8606 rev. 1.05 www.monolithicpower.com 5 12/22/2015 mps proprietary information. patent protec ted. unauthorized photocopy and duplication prohibited. ? 2015 mps. all rights reserved. pin functions pin # name description 1 agnd analog ground. 2 freq frequency. set during ccm operation. connec t a resistor to in for line feed-forward. 3 fb feedback. sets the output voltage from the t ap of an external resistor divider from the output to gnd. 4 ss/trk soft-start. connect on external capacitor to program the soft start time for the switch mode regulator. 5 en en=1 to enable the mp8606. for automatic start-up, connect en pin to vin with 100k ? resistor. 6 pgood power-good open-drain output. high output indicates that the output is within +/- 10% of the regulation value. low output indi cates that the output is out of +/-10% window. there is a 0.5 ms delay from fb 90% to pgood goes high. 7 bst bootstrap. connect a capacitor between this pin and sw to provide a floating supply for the high-side gate driver. 8, 21, 22 sw switch node. connect to the inductor. co nnects to the internal high-side and low- side power mosfet switches. all sw pins must be connected together externally. 9-16 pgnd power ground. connect these pins to the negative terminals of the input and output capacitors using large copper areas. connect to agnd through a single point. 17, 19, 20 in input supply. powers the high-side switch. requires a decoupling capacitor to ground close to this pin to reduce switch ing spikes. connect all in pins together externally. 18 vcc bias supply. power both the internal cont rol circuitry and gate drivers. requires a decoupling capacitor to ground close to this pin.
mp8606 ? 6a, 6.5v synchrono us step-down converter mp8606 rev. 1.05 www.monolithicpower.com 6 12/22/2015 mps proprietary information. patent protec ted. unauthorized photocopy and duplication prohibited. ? 2015 mps. all rights reserved. typical performanc e characteristics v in =5v, v out =1v, f s =1mhz, t a =+25c, unless otherwise noted. r8 ns 100k r6 pgood vcc vin gnd c5 vcc freq pgood en agnd pgnd ss/trk fb sw bs in mp8606 15nf c6 r2 30k c4 270pf c8 0r r5 100k en r9 10 c1a c1d 150k r7 ss/trk sw sw c2b c2d gnd vout 0 r10 150k r4 22k r1 0 r3 we 744314076 c1b r11 ns c2a c3 c1c c2c c2e ns 0 5 10 15 20 25 30 35 40 0123456 -0.5 -0.4 -0.3 -0.2 -0.1 0 0.1 0.2 0.3 0.4 0.5 4.5 4.7 4.9 5.1 5.3 5.5 -0.50 -0.40 -0.30 -0.20 -0.10 0.00 0.10 0.20 0.30 0.40 0.50 0123456 1000 1010 1020 1030 1040 1050 1060 1070 1080 1090 -40 -20 0 20 40 60 80 100 120 140 0 200 400 600 800 1000 1200 0.01 0.1 1 10 0 10 20 30 40 50 60 70 80 90 100 0.01 0.1 1 10
mp8606 ? 6a, 6.5v synchrono us step-down converter mp8606 rev. 1.05 www.monolithicpower.com 7 12/22/2015 mps proprietary information. patent protec ted. unauthorized photocopy and duplication prohibited. ? 2015 mps. all rights reserved. typical performanc e characteristics (continued) v in =5v, v out =1v, f s =1mhz, t a =+25c, unless otherwise noted. pgood, shutdown through en i out =0a pgood, shutdown through en i out =6a v out 20mv/div i out 2a/div v out /ac 10mv/div v in /ac 200mv/div v sw 2v/div i l 5a/div v out /ac 10mv/div v in /ac 200mv/div v sw 5v/div i l 5a/div v en 5v/div v out 500mv/div v pgood 2v/div i l 5a/div v en 5v/div v out 500mv/div v pgood 2v/div i l 5a/div v en 5v/div v out 500mv/div v pgood 2v/div i l 5a/div v sw 2v/div v out 500mv/div v in 2v/div i l 5a/div v sw 2v/div v out 500mv/div v in 2v/div i l 5a/div v en 5v/div v out 500mv/div v pgood 2v/div i l 5a/div startup through v in i out =0a startup through v in i out =6a pgood, startup through en i out =0a pgood, startup through en i out =6a steady state i out =0.6a steady state i out =6a
mp8606 ? 6a, 6.5v synchrono us step-down converter mp8606 rev. 1.05 www.monolithicpower.com 8 12/22/2015 mps proprietary information. patent protec ted. unauthorized photocopy and duplication prohibited. ? 2015 mps. all rights reserved. typical performanc e characteristics (continued) v in =5v, v out =1v, f s =1mhz, t a =+25c, unless otherwise noted. startup through en i out =6a shutdown through en i out =0a v out 500mv/div v in 2v/div v sw 2v/div i l 5a/div v out 500mv/div v in 2v/div v sw 2v/div i l 5a/div v out 500mv/div v sw 2v/div i l 5a/div v out 500mv/div v sw 2v/div i l 5a/div v out 500mv/div v en 5v/div v sw 2v/div i l 5a/div v out 500mv/div v en 5v/div v sw 2v/div i l 5a/div v out 500mv/div v en 5v/div v sw 2v/div i l 5a/div v out 500mv/div v en 5v/div v sw 2v/div i l 5a/div shutdown through en i out =6a shutdown through v in i out =0a short circuit protection startup through en i out =0a shutdown through v in i out =6a over-current protection
mp8606 ? 6a, 6.5v synchrono us step-down converter mp8606 rev. 1.05 www.monolithicpower.com 9 12/22/2015 mps proprietary information. patent protec ted. unauthorized photocopy and duplication prohibited. ? 2015 mps. all rights reserved. typical performanc e characteristics (continued) v in =5v, v out =1v, f s =1mhz, t a =+25c, unless otherwise noted. v out /ac 20mv/div v in 1v/div v out /ac 20mv/div v in 1v/div i l 1a/div output voltage with noisy input voltage v in =5v, v noisepp =1.24v transient performance with noisy input voltage v in =5v, v noisepp =1.24v
mp8606 ? 6a, 6.5v synchrono us step-down converter mp8606 rev. 1.05 www.monolithicpower.com 10 12/22/2015 mps proprietary information. patent protec ted. unauthorized photocopy and duplication prohibited. ? 2015 mps. all rights reserved. functional block diagram figure 1?functional block diagram
mp8606 ? 6a, 6.5v synchrono us step-down converter mp8606 rev. 1.05 www.monolithicpower.com 11 12/22/2015 mps proprietary information. patent protec ted. unauthorized photocopy and duplication prohibited. ? 2015 mps. all rights reserved. operation pwm operation the mp8606 is a fully-integrated, synchronous rectified, step-down switch converter. the device uses constant-on-time (cot) control to provide fast transient response and easy loop stabilization. at the beginning of each cycle, the high-side mosfet (hs-fet) turns on whenever the feedback voltage (v fb ) is lower than the reference voltage (v ref )?a low v fb indicates insufficient output voltage. the input voltage and the frequency-set resistor determine the on period as follows: 7 on in 5.8 r (k ) t(ns) v (v) 0.48 ?? ? ? (1) after the on period elapses, the hs-fet enters the off state. by cycling hs-fet between the on and off states, the converter regulates the output voltage. the integrated low-side mosfet (ls-fet) turns on when the hs-fet is in its off state to minimize the conduction loss. shoot-through occurs after both hs-fet and ls-fet are turned on at the same time, causing a dead short between input and gnd. shoot- through dramatically reduces efficiency, and the mp8606 avoids this by internally generating a dead-time (dt) between when hs-fet is off and ls-fet is on, ls-fet is off and hs-fet is on. the device enters either heavy-load operation or light-load operation depending on the amplitude of the output current. heavy-load operation figure 2?heavy load operation during heavy-load operation?when the output current is high?the mp8606 enters continuous- conduction mode (ccm) where the hs-fet and ls-fet repeat the on/off operation described for pwm operation, the inductor current never goes to zero, and the switching frequency (f sw ) is fairly constant. figure 2 shows the timing diagram during this operation. light-load operation during light-load operation?when the output current is low?the mp8606 automatically reduces the switching frequency to maintain high efficiency, and the inductor current drops near zero. when the inductor current reaches zero, the ls-fet driver goes into tri-state (high z). the current modulator controls the ls-fet and limits the inductor current to around -1ma as shown in figure 3. hence, the output capacitors discharge slowly to gnd through ls-fet, r1, and r2. this operation greatly improv es device efficiency when the output current is low. figure 3?light load operation light-load operation is also called skip mode because the hs-fet does not turn on as frequently as during heavy-load conditions. the frequency at which the hs-fet turns on is a function of the output current?as the output current increases, the time period that the current modulator regulates becomes shorter, and the hs-fet turns on more frequently. the switching frequency increases in turn. the output current reaches the critical level when the current modulator time is zero, and can be determined using the following equation: in out out out sw in (v v ) v i 2lf v ?? ? ? ?? (2) the device reverts to pwm mode once the output current exceeds the critical level. after that, the switching frequency stays fairly constant over the output current range.
mp8606 ? 6a, 6.5v synchrono us step-down converter mp8606 rev. 1.05 www.monolithicpower.com 12 12/22/2015 mps proprietary information. patent protec ted. unauthorized photocopy and duplication prohibited. ? 2015 mps. all rights reserved. figure 4? floating driver and bootstrap charging the floating power mosfet driver is powered by an external bootstrap capacitor. this floating driver has its own uvlo protection with a rising threshold of 1.4v and a hysteresis of 150mv. the bootstrap capacitor is charges from vcc through n1 (fig. 4). n1 turns on when the ls- fet turns on and turns off when the ls-fet turns off. a schottky diode is recommended to be placed between vcc and bst to help maintain bst voltage at light load operation. switching frequency mp8606 uses constant-on-time (cot) control because there is no dedicated oscillator in the ic. the input voltage is feed-forwarded to the on- time one-shot timer through the resistor r7. the duty ratio is kept as v out /v in , and the switching frequency is fairly constant over the input voltage range. the switching frequency can be determined with the following equation: 6 sw 7in delay in out 10 f(khz) 5.8 r (k ) v (v) t(ns) v(v) 0.48 v (v) ? ?? ?? ? (3) where t delay is the comparator delay, and equals approximately 40ns. mp8606 is optimized to operate at high switching frequency with high efficiency. high switching frequency makes it possible to use small-sized lc filter components to save system pcb space. ramp compensation jitter occurs in both pwm and skip modes when noise in the v fb ripple propagates a delay to the hs-fet driver, as shown in figures 5 and 6. jitter can affect system stability, with noise immunity proportional to the steepness of v fb ?s downward slope. however, v fb ripple does not directly affect noise immunity. v re f v fb hs driver v noise j itter v s l o pe1 figure 5?jitter in pwm mode v fb hs driver jitter v ref v slope2 v noise figure 6?jitter in skip mode when using ceramic output capacitors, the esr ripple is not sufficient to stabilize the system, and the system requires external ramp compensation. i i fb i c4 i r4 i fb figure 7?simplified circuit in pwm mode with external ramp compensation
mp8606 ? 6a, 6.5v synchrono us step-down converter mp8606 rev. 1.05 www.monolithicpower.com 13 12/22/2015 mps proprietary information. patent protec ted. unauthorized photocopy and duplication prohibited. ? 2015 mps. all rights reserved. figure 7 shows a simplified external ramp compensation (r4 and c4) for pwm mode, with hs-fet off. chose r1, r2, and c4 of the external ramp to meet the following condition: 12 sw 4 1 2 rr 11 2f c 5 rr ?? ? ?? ?? ?? ? ? ?? (4) where: r4 c4 fb c4 iiii ??? (5) the downward slope of the v fb ripple can be estimated as: ref slope1 44 v v rc ? ? ? (6) reducing either r4 or c4, as seen from equation (6), can control some of the instability in pwm mode. if the condition from equation (4) prevents reductions to c4, then only reduce r4. v slope1 has an expected range between 20v/ms to 40v/ms based on bench experiments. the external ramp is not necessary for other types of capacitors with higher esr such as poscaps. figure 8?simplified circuit in pwm mode without external ramp compensation figure 8 shows the equivalent circuit in pwm mode with the hs-fet off and without an external ramp circuit. the esr ripple dominates the output ripple. the downward slope of the v fb ripple is: ref slope1 esr v v l ?? ? (7) designing v slope1 ?with a recommended range between 15v/ms to 30v/ms based on bench experiments?requires using the minimum esr value of the output capacitor with a small-value inductor. an external ramp does not affect v slope2 in skip mode. figure 9 shows an equivalent circuit with hs-fet off and the current modulator regulating the ls-fet. instead, the downward slope of the v fb ripple can be modeled with the following equation that excludes i mod : ?? ref slope2 12 out v v rr c ? ? ?? (8) figure 9?simplified circuit in skip mode to keep the system stable during light load condition, the values of the fb resistors should be better in the range of 5k ? to 50k ? . it is recommended to keep the v slope2 value between 0.4mv/ms to 0.8mv/ms. when using a large-esr capacitor on the output, add a ceramic capacitor with a value of 10uf or less to in parallel to minimize the effect of esl. soft start/stop mp8606 employs a soft start/stop (ss) mechanism to ensure smooth output during power up and power shut-down. when the en pin goes high, the internal ss voltage slowly ramps up. the output voltage smoothly ramps up with the ss voltage. once ss voltage rises above the v ref , it continues to ramp up while the pwm comparator only compares the v ref with the fb voltage. at this point, the soft start finishes and it enters steady state operation. the
mp8606 ? 6a, 6.5v synchrono us step-down converter mp8606 rev. 1.05 www.monolithicpower.com 14 12/22/2015 mps proprietary information. patent protec ted. unauthorized photocopy and duplication prohibited. ? 2015 mps. all rights reserved. ss time is programmable through the capacitor connected between ss pin and agnd. when the en pin goes low, an internal current source discharges the internal ss voltage. once the ss voltage falls below the v ref , the pwm comparator will only compare the v ref to the ss voltage. the output voltage will decrease smoothly with the ss voltage until the voltage level zeros out. power-good (pg) the pg pin is the open drain of a mosfet that connects to v cc or some other voltage source through a resistor (ex. 100k). the mosfet turns on with the application of an input voltage so that the pg pin is pulled to gnd before ss is ready. after fb voltage reaches 90% of v ref , the pg pin is pulled high after a 0.5ms delay. when the fb voltage drops to 85% of v ref , the pg pin will be pulled low. over-current protection (ocp) and short- circuit protection (scp) mp8606 has cycle-by cycle over-current limit control. the inductor current is monitored during the on state. for MP8606DL, the hs-fet turns off when the inductor current exceeds the current limit and the ocp timer?set at 50 s?starts. the ocp triggers if the inductor current reaches or exceeds the current limit every cycle in those 50 s. the mp8606 short-circuit protection (scp) occurs when dead shorts occur?when the inductor current exceeds the current limit and the fb voltage is lower than 50% of the v ref . for MP8606DL, it enters hiccup mode, during scp/ocp. it periodically restarts the part when the inductor peak current exceeds the current limit and v fb drops below the under-voltage (uv) threshold. typically, the uv threshold is 50% below the ref voltage. in ocp/scp, MP8606DL will disable both the hsfet and lsfet, discharge internal soft-start cap, and then automatically try to soft-start again. if the over- current circuit condition still holds after soft-start ends, it repeats this operation cycle until the over-current circuit condition disappears, and output rises back to regulation level. over/under-voltage protection (ovp/uvp) mp8606 monitors the output voltage through a resistor-divided feedback (fb) voltage to detect over and under voltage on the output. when the fb voltage is higher than 125% of the v ref , it will trigger the ovp. once it triggers the ovp, the ls-fet is always on while the hs-fet is off. it needs to power cycle to turn on again. conversely, the uvp triggers when the fb voltage falls below 50% of the v ref (0.6v) usually uvp accompanies a drop in the current limit and this results in scp. uvlo protection mp8606 has under-voltage lock-out protection (uvlo). when the input voltage is higher than the uvlo rising threshold voltage, the mp8606 powers up. it shuts off when the input voltage is lower than the uvlo falling threshold voltage. this is non-latch protection. thermal shutdown the mp8606 employs thermal shutdown by internally monitoring the junction temperature of the ic. if the junction temperature exceeds the threshold value (typically 150oc), the converter shuts off. this is non-latch protection. there is about 20oc hysteresis. once the junction temperature drops around 130oc, it initiates a soft start.
mp8606 ? 6a, 6.5v synchrono us step-down converter mp8606 rev. 1.05 www.monolithicpower.com 15 12/22/2015 mps proprietary information. patent protec ted. unauthorized photocopy and duplication prohibited. ? 2015 mps. all rights reserved. application information setting the output voltage the output voltage is set by using a resistive voltage divider from the output voltage to the fb pin. the use of low-esr ceramic output capacitors requires adding an external voltage ramp to the fb through r4 and c4. choose an r2 value between 5k ? and 40k ? , then determine r1 using the following equation: 1 ref ramp 4 2outref ramp 1 r 1 vv 1 2 1 r r(v v v ) 2 ? ? ? ??? (9) using the v ramp value derived from equation (16). for sample feedback resistor values and output voltages, see the design example section on page 11. input capacitor the input current to the step-down converter is discontinuous and therefore requires a capacitor to supply the ac current to the step-down converter while maintaining the dc input voltage. ceramic capacitors are recommended for best performance and should be placed as close to the v in pin as possible. capacitors with x5r and x7r ceramic dielectrics are recommended because they are fairly stable with temperature fluctuations. the capacitors must also have a ripple current rating greater than the maximum input ripple current of the converter. the input ripple current can be estimated as follows: out out cin out in in vv ii (1 ) vv ?? ?? (10) the worst-case condition occurs at v in = 2v out , where: out cin i i 2 ? (11) for simplification, choose the input capacitor with an rms current rating greater than half of the maximum load current. the input capacitance value determines the input voltage ripple of the converter. if there is an input voltage ripple requirement in the system, choose the input capacitor that meets the specification. the input voltage ripple can be estimated as follows:: out out out in sw in in in iv v v(1) fc v v ?? ? ?? ? (12) under worst-case conditions where v in = 2v out : out in sw in i 1 v 4f c ??? ? (14) output capacitor the output capacitor is required to maintain the dc output voltage. ceramic or poscon capacitors are recommended. the output voltage ripple can be estimated by: out out out esr sw in sw out vv 1 v(1)(r ) fl v 8fc ?? ?? ? ? ??? (14) where r esr is the esr value of c out . for ceramic capacitors, the capacitance dominates the impedance at the switching frequency and is the primary contributor to the output voltage ripple. for simplification, the output voltage ripple can be estimated by: out out out 2 sw out in vv v(1) 8f lc v ?? ?? ??? (15) the output voltage ripple caused by esr is very small for ceramic capacitors, so it needs an external ramp to stabilize the system. the voltage ramp is expected to be around 30mv. the external ramp can be generated through resistor capacitor c 4 , using the following equation: in out on ramp 44 (v v ) t v rc ?? ? ? (16) the c 4 should meet the following requirement: 12 sw 4 1 2 rr 11 () 2f c 5rr ? ?? ?? ? ? (17)
mp8606 ? 6a, 6.5v synchrono us step-down converter mp8606 rev. 1.05 www.monolithicpower.com 16 12/22/2015 mps proprietary information. patent protec ted. unauthorized photocopy and duplication prohibited. ? 2015 mps. all rights reserved. in the case of poscap or electrolytic capacitors, the esr dominates the impedance at the switching frequency. the ramp voltage generated from the esr is high enough to stabilize the system, and does not require an external ramp. a minimum esr value of 12m ? is recommended to ensure stable operation of the converter. for simplification, the output ripple can be approximated as: out out out esr sw in vv v(1)r fl v ?? ?? ? ? (18) maximum output capacitor limitation should be also considered in design application. mp8606 has an around 1ms soft-start time period. if the output capacitor value is too high, the output voltage can?t reach the design value during the soft-start time, and then it will fail to regulate. the maximum output capacitor value c o_max can be limited approximately by: o_max lim_avg out ss out c(i i)t/v ??? (19) where, i lim_avg is the average start-up current during soft-start period. t ss is the soft-start time. inductor the inductor is necessary to supply constant current to the output load while being driven by the switched input voltage. a larger-value inductor will result in less ripple current that will result in lower output ripple voltage. however, a larger-value inductor will have a larger physical footprint, higher series resistance, and/or lower saturation current. a good rule for determining the inductance value is to design the peak-to- peak ripple current in the inductor to be in the range of 30% to 40% of the maximum output current, and that the peak inductor current is below the maximum switch current limit. the inductance value can be calculated by: out out sw l in vv l(1) fi v ??? ?? (20) where i l is the peak-to-peak inductor ripple current. the inductor should not saturate under the maximum inductor peak current, where the peak inductor current can be calculated by: out out lp out sw in vv ii (1 ) 2f l v ?? ?? ? (21) design example some design examples and recommended maximum output capacitor value with typical outputs are provided below: table 1?v out =1v (l=0.47h) v in (v) v out (v) r7 ( ? ) r4 ( ? ) c4 ( f) r1 ( ? ) r2 ( ? ) f sw (hz) 5 1 169 k 442 k 100p 20 k 30 k 1000k table 2? v out =1.8v (l=2h) v in (v) v out (v) r7 ( ? ) r4 ( ? ) c4 ( f) r1 ( ? ) r2 ( ? ) f sw (hz) 5 1.8 740k 442k 270p 42.2k 20k 400k table 3? v out =2.5v (l=1h) v in (v) v out (v) r7 ( ? ) r4 ( ? ) c4 ( f) r1 ( ? ) r2 ( ? ) f sw (hz) 5 2.5 630k 442k 220p 52k 15k 650k table 4? v out =3.3v (l=1h) v in (v) v out (v) r7 ( ? ) r4 ( ? ) c4 ( f) r1 ( ? ) r2 ( ? ) f sw (hz) 5 3.3 620k 390k 220p 50k 10k 860k the detailed application schematic is shown in figure 10. the typical performance and circuit waveforms have been shown in the typical performance characteristics section. for more possible applications of this device, please refer to related evaluation board data sheets.
mp8606 ? 6a, 6.5v synchrono us step-down converter mp8606 rev. 1.05 www.monolithicpower.com 17 12/22/2015 mps proprietary information. patent protec ted. unauthorized photocopy and duplication prohibited. ? 2015 mps. all rights reserved. r8 ns 100k r6 pgood vcc vin gnd c5 vcc freq pgood en agnd pgnd ss/trk fb sw bs in mp8606 15nf c6 r2 tbd c4 tbd c8 0r r5 100k en r9 10 c1a ns c1d tbd r7 ss/trk sw sw c2b c2d gnd vout 0 r10 tbd r4 tbd r1 0 r3 tbd c1b r11 ns c2a c3 c1c c2c c2e ns figure 10?detailed application schematic layout recommendation 1) put the input capacitors as close to the in and gnd pins as possible on the same layer. 2) put the decoupling capacitor as close to the v cc and gnd pins as possible. on the same layer. 3) keep the switching node sw short and away from the feedback network. 4) the external feedback resistors should be placed next to the fb pin. make sure that there is no via on the fb trace. 5) keep the bst voltage path (bst, c3, and sw) as short as possible. 6) four-layer layout is recommended to achieve better thermal performance. 7) keep freq signal away from noise signals, like sw, bst and high di/dt vin connections close to the mp8606 vin leads. the vin pin of frequency setting resistor (r7) should connect to a quiet vin node at the front of input decoupling cap.
mp8606 ? 6a, 6.5v synchrono us step-down converter notice: the information in this document is subject to change wi thout notice. please contact m ps for current specifications. users should warrant and guarantee that third party intellectual property rights ar e not infringed upon when integrating mps products into any application. mps will not assume any legal responsibility for any said applications. mp8606 rev. 1.05 www.monolithicpower.com 18 12/22/2015 mps proprietary information. patent protec ted. unauthorized photocopy and duplication prohibited. ? 2015 mps. all rights reserved. package information qfn-18 (3mmx4mm)

▲Up To Search▲

Price & Availability of MP8606DL

	To Download MP8606DL Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .